Life Fitness Fit-1 Bedienungsanleitung

FIT SERIES FIT-1Part # 7317701Rev B.Revision:8/30/021ASSEMBLY INSTRUCTIONS

STEP 9:FIGURE 910STEP 8:FIGURE 85118 7767873753/8 X 4-1/4” (106m) 67 2 7• Insert one 3-5/16” PIVOT SHAFT (47) into the PEDESTAL (7) as shown in FIGU

STEP 11:FIGURE 1111STEP 10:FIGURE 1046 61576BLACK 7773753/8 X 4-1/4” (106m) 67 1211• SECURELY assemble the SEAT SUPPORT (11) to the ADJUSTABLE SE

STEP 13:FIGURE 1312STEP 12:FIGURE 1277 BLACK763/8 X 1-1/4” (32m) 61114276BLACK 77737512• SECURELY assemble the BACK PAD SUPPORT (15) to the ADJUSTA

STEP 14:FIGURE 1413BLACK 77753/8 X 3” (73m) 651543• SECURELY assemble the BACK PAD (43) to the BACK PAD SUPPORT (15) using two BLACK RH CAPS (77), t

STEP 17:FIGURE 1714STEP 16:FIGURE 16141/2 X 3” 5773137678737513 153 3/8 X 4” (97m)• SECURELY assemble the SWIVEL SUPPORT (13) to the BASE (1) using

15STEP 18:FIGURE18 93637• Slide two 5” ACCORIDIAN SLEEVES(36) over the shafts on the PIVOT ARM(9) as shown in FIGURE 18.• Slide two PILLOW BLOCKS (3

16STEP 20:FIGURE 20• Insert one 5-1/2” TAPPED PIVOT SHAFT (41) into the PIVOT ARM (9).• SECURELY assemble the PRESS ADJUST PLATE (26) to the PIVOT A

STEP 24:FIGURE 2417• Insert two GUIDE RODS (27) through the BOTTOM SHROUD BRACKET (20) and into the BASE (1) as shown on FIGURE 24.• Slide two 3

STEP 25:FIGURE 2518• CAREFULLY assemble the STACK BOOM (8) over the GUIDE RODS (27) as shown in FIGURE 25.27 8STEP 26:FIGURE 26• LOOSELY assemble

19FIGURE 27STEP 27:64 3/8 X 2-1/2” (67m) 85038FIGURE 28STEP 28:737862 3/8 X 1-3/4” (43m)217675• Slide the two 13/16” SHAFT COLLARS (50) to the top o

PARTS LISTPART #04-132504-132604-132704-132804-133004-133504-132904-133404-133104-133804-133604-133704-1332B04-1339B04-133304-134002-129401-207301-200

FIGURE 2920STEP 29:• SECURELY assemble two 4-1/2” PULLEYS (38) to the BOOM (8) using two BLACK RH CAPS (77), two RH CAPS (78), two3/8 X 2-3/4” BOLTS

21FIGURE 30STEP 30:• Route the LEG CABLE (45) through the SWIVEL (14) and assemble two 4-1/2” PULLEYS (38) to the SWIVEL (14) using fourBLACK RH CAPS

22FIGURE 32STEP 32:737862 3/8 X 1-3/4” (43m)387675• Route the LEG CABLE (45) around one 4-1/2” PULLEY (38) and assemble the PULLEY (38) to the low

23FIGURE 33STEP 33:4578763873 62• Route the LEG CABLE (45) through the bracket on the BASE (1) and assemble one 4-1/2” PULLEY (38) to the bracket on

STEP 34:FIGURE 3424• Assemble the LOW ROW BAR (34) to the LEG CABLE (45) using two SNAP LINKS (40) and one 12-LINK CHAIN (48) asshown in FIGURE 34.

STEP 35:FIGURE 3525• Adjustments can be made in the above locations to set the correct amount of tension in the cables.• If upon completion of a

Clean:• Upholstery with mild soap and water.• Guide rods with a cotton cloth.• Hand grips with mild soap and water.• Frame damage can be repaired with

360 3/8 X 1” (25m) BOLT61 3/8 X 1-1/4” (32m) BOLT62 3/8 X 1-3/4” (43m) BOLT64 3/8 X 2-1/2” (67m) BOLT68 3/8 X 2-3/4” (70m) BOLT63 3/8 X 3-1/2” (90

467 3/8 X 4-1/4” (106m) BOLT69 3/8 X 6-1/2” (164m) BOLT72 3/8 X 3” (76m) BUTTON HEAD BOLT57 1/2 X 3” SHOULDER BOLT551”FLANGE SPACER71 3/8 X 1” (25m

STEP 1:FIGURE 15• LOOSELY assemble the REAR UPRIGHT (5) to the BASE (1) to the using four RH CAPS (78), two 3/8 X 3-1/2” BOLTS (63), four3/8” SAE WAS

STEP 2:FIGURE 26• LOOSELY assemble the LEFT and RIGHT BOOM SUPPORTS (3 & 4) to the REAR UPRIGHT (5) using four RH CAPS (78), two3/8 X 3” BOLTS (6

FIGURE 37STEP 3:FIGURE 4STEP 4:• SECURELY assemble one STORAGE PEG (25) to the LEFT BOOM SUPPORT (3) using one RH CAPS (78), one 3/8 X 1” BOLT(60), o

STEP 6:FIGURE 68STEP 5:FIGURE 5 212• Pull back on the SPRING PIN and slide the ADJUSTABLE SEAT (12) over the BENCH FRAME (2) as shown in FIGURE 5. 23

9STEP 7:TIGHTEN!• Securely tighten all loose frame connections made to this point, then proceed to snap RH CAPS(78) over the RH WASHERS (76) on all t