1807 BODYSYSTEMWORKOUT CENTERCLASS HPART # 7052601REV. BRevision: 07/09/01USER’S GUIDEWARNING:Read and follow all directionsfor each step to insure p
10FIGURE 5 13STEP 5: 93/8 X 1” 15 20 401234561/2 1/2 1/2 1/2 1/2 1/2• To assemble the SEAT PAD (13) to the WOLFF SLEEVE (4), start by sliding two HI
11FIGURE 6 9STEP 6:143/8 X 1” 15 20 4• To assemble the BACK PAD (14) to the WOLFF SLEEVE (4), slide the two remaining HINGE TABS (9) over the PIN o
12FIGURE 7 723STEP 7:1201234561/2 1/2 1/2 1/2 1/2 1/2• Insert one 1-3/4” SQ. END CAP (23) into the top of the LEG EXTENSION NECK (7) as shown in FI
FIGURE 8STEP 8:233213• Insert three 1-3/4” SQ. END CAPS (23) into the ends of the LEG EXTENSION (8) as shown in FIGURE 8.• Insert two 1/2” FLANGE
14FIGURE 9STEP 9: 2• When ready to perform LEG CURLS or LEG EXTENSION, pull up slowly on the front of the BENCH FRAME (2) and allowthe U-PIN (10) t
15FIGURE 10 1STEP 10: 3• Set the HEIGHT ADJUSTMENT BAR (3) across the UPRIGHT FRAME (1) as shown in FIGURE 10, for performing INCLINE,or MILITARY PR
MAINTENANCEMODEL #________________________SERIAL #_________________________DATE OF PURCHASE: _____________DEALERS NAME: _________________DEALERS PHONE
17NOTES:LIMITED WARRANTYParaBody extends the following LIMITED WARRANTY to the original owner of the ParaBody products. The Warranty terms apply to IN
INTERNATIONAL OFFICESLife FitnessAtlantic BVAtlantic HeadquartersBijdorpplein 25-312992 LB BarendrechtThe NetherlandsPhone: (180) 646 666Fax: (180) 6
THERE IS A RISK ASSUMED BY INDIVIDUALS WHO USE THIS TYPE OFEQUIPMENT. TO MINIMIZE RISK FOLLOW THESE RULES!1. Before using, read all the warnings and
IMPORTANT NOTESPlease note:Tools Required for Assembly* Thank you for purchasing the ParaBody 807 Gym System. Please read these instructions thorou
1 Square = 1’ X 1’41’ 2’ 3’4’5’6’7’1’5’4’3’2’
PARTS LISTKEY1234567891011121314151617181920212223242526272829303132335PART #7058908640750861110026406602640780264073026407202602470264064016406501612
01234561/2 1/2 1/2 1/2 1/2 1/2FIGURE 1STEP 1:28 4 251031• Attach eight PARAGLIDE STRIPS (31) to the WOLFF SLEEVE (4) (FOUR ON EACH END) as shown in
7FIGURE 2STEP 2: 410 5 2• Pull back the SPRING PIN on the WOLFF SLEEVE (4) and slide it over the end of the BENCH FRAME (2) as shown inFIGURE 2. Eng
8FIGURE 3 3333 1STEP 3:• Secure the WOLFF SLEEVE (4) in place with one THUMBSCREW (29).• Insert four 2” SQ. END CAPS (33) into the BASE TUBES of t
9FIGURE 4 131STEP 4:30 6 29• Attach eight PARAGLIDE STRIPS (31) to both UPRIGHT TUBES on the UPRIGHT FRAME (1) (FOUR ON EACH END) asshown in FIGURE
Kommentare zu diesen Handbüchern