Life Fitness CM3 Bedienungsanleitung

CM3 GYM SYSTEMUSER’S GUIDEWARNING: Read and follow all directionsfor each step to ensure properassembly of this product.CLASS HPART # 7657801REV. BVer

10CABLING DIAGRAM 5P13-0112-4

11STEP 1:A. Loosely assemble two Base Plates (11) to the Front Base (1) and the Base Connector (3) usingfour 3/8 x 3-3/4" Bolts (57) and four 3/8

12STEP 2:A. Loosely assemble the Right Arm (5) and Rear Base (4) using two 3/8 x 3-3/4" Bolts (57), two 3/8"Washers (64) and two 3/8" L

13FIGURE 4FIGURE 3Make sure that the Weight Plates (21) are assembled as shown in Figure 3 and the Head PlateAssembly (23) is assembled as shown in Fi

14STEP 5:A. Insert two Guide Rods (18) into the Rear Base (4) as shown in Figure 5. (Note: If you purchasedthe CM3 Shroud Option, place the Guide Rods

STEP 6:A. Swing the Guide Rods (18) into the guide rod bushings in the Right Boom Plate (14) and LeftBoom Plate (15) as shown in Figure 6.B. Loosely a

STEP8:A. Securely assemble the Three Prong Knob (43) to the Front Base (1) as shown.B. Insert the Seat Adjust Assembly (7) into the Front Base (1) as

17STEP 9:A. Detach Short Cable from both Rear Guide Cables (74) as shown in Figure 9 (B).B. Slide Long Cables of Rear Guide Cables (74) through eyelet

IMPORTANT! UNCOIL AND STRAIGHTEN ALL CABLES TO REMOVE ALL TWISTS BEFOREINSTALLING.STEP 10:A. Assemble the Weight Stack Pin (27) to theHead Plate Assem

STEP 11:A. Loop the Weight Stack Cable (29) around one 3-1/2" Pulley (37). B. Assemble the 3-1/2" Pulley (37) with the Weight Stack Cable (2

TABLE OF CONTENTSSafety Statement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

STEP 12:A. Loop the Boom Cable (32) around one 3-1/2" Pulley (37).B. Assemble the 3-1/2" Pulley (37) with the Boom Cable (32) looped around

STEP 13:A. Securely assemble the ball end of the Leg Cable (30) and one 3-1/2" Pulley (37) to the LegPedestal (8), using two 3/8 x 3-3/4" Bo

22FIGURE 14STEP 14:A. Securely assemble one 3-1/2"Pulley (37) to the Pulley Plates (10),using one 3/8 x 1-3/4" Bolt (53) andone 3/8" Lo

STEP 16:A. Route the Arm Cable (31) through the Left Arm (6) as shown in Figure 16.B. Loop the Arm Cable (31) around one 4-1/2" Pulley (38).C. Se

STEP 17:A. Securely assemble two 3-1/2" Pulleys (37) to the Base Plates (11), using two 3/8 x 3-3/4" Bolts(57), one 3/8 x 1" Spacer (51

STEP 18:A. Route the Arm Cable (31) through the Right Arm (5) as shown in Figure 18.B. Loop the Arm Cable (31) around one 4-1/2" Pulley (38).C. S

STEP 19:A. Insert Arm Cable (31) ends through Swivel Pulley Assemblies (72).B. Insert Swivel Pulley Assemblies (72) into Left Arm (5) and Right Arm (6

STEP 21:A. Assemble two Roller Pads (17) to the Leg Pedestal (8) using one 3/4 x 18" Tube (24), fourPlastic Washers (45), two Roller Pad Caps (44

STEP 22:A. Make adjustments to the cables’ tension at the locations shown in Figure 22.B. Adjust the Turnbuckle on each Guard Cable (65) to change the

MAINTENANCEOWe recommend cleaning your product (pads and frame) on a regular basis, using warmsoapy water. Touch-up paint can be purchased from your L

IMPORTANT NOTESThank you for purchasing the Life Fitness CM3 Gym System. Please read these instructions thoroughly and keep them for future reference.

30WARRANTYLife Fitness extends the following LIMITED WARRANTY to the original owner of the Life Fitness products. The Warrantyterms apply to IN HOME U

31LIFEFITNESS ASIA PACIFIC LTDRoom 2610, Miramar Tower132 Nathan RoadTsimshatsui, KowloonHONG KONGTelephone: (+852) 2891.6677FAX: (+852) 2575.6001LIFE

CM3 FOOTPRINT1 SQUARE = 1' X 1'MINIMUM REQUIRED USABLE SPACE:Length = 90 inches (229 cm) 7' 6"Width = 103 inches (262 cm) 8'

5PARTS LISTNote: Some of the components may be pre-assembled.1 ACU04-0906 FRONT BASE 12 ACU04-0909-107 UPRIGHT 13 ACU04-0907 BASE CONNECTOR 14 ACU04-0

CABLE END ASSEMBLY:Slide parts onto cable in the following order: Item 2, Item 4, Item 3.Insert cable end into Item 1.Slide entire assembly over Item

7CABLING DIAGRAM 2P13-0112-2

8CABLING DIAGRAM 3P13-0112-1

9CABLING DIAGRAM 4P13-0112-5